StingerWorxVenom 300
.30 Cal / 7.62mm suppressor · HUB 1.375x24 interface · specs and compatibility from the manufacturer
Notable features
- HUB Compatible
- Multi-Caliber
- Brake on the Front of the Suppressor
- User Serviceable
- TBAC Summit Tested
length
8.2″
weight
17oz
MSRP
$949
length
8.2″
weight
17oz
calibers
5.56–.30
material
Titanium · Aluminum
interface
HUB 1.375x24
MSRP
$949
- Overall length
- 8.2″
- Class
- .30 Cal / 7.62mm
- n
- 646
- Range
- 2.5″–14″
- Median
- 7.2″
- Diameter
- 1.75″
- Weight
- 17 oz
- Material
- Titanium (Mount & Blast Chamber) + 7075 Aluminum (Body & Stack)
- Finish / treatment
- Type III Hard Coat Anodized, Cerakote
- Max caliber
- .30 Cal / 7.62mm
- Base interface
- HUB 1.375x24
- Front cap
- StingerWorx MDS
- Full-auto rated
- No
- Maintenance
- User serviceable
- Brake on the front
- The maker sells a brake end cap that screws onto the front of the suppressor
- Brakes that fit:
- StingerWorx Suppressor Brake (Titanium)
- StingerWorx Suppressor Brake (Aluminum)
- MSRP
- $949
Longer than most .30 Cal / 7.62mm suppressors
Length compared against the 646 .30 Cal / 7.62mm suppressors in the catalog that publish one. Quartile basis; a value inside the middle half carries no note.
Prices are manufacturer's suggested retail (MSRP). What you pay may differ.
Is something on this page wrong?
- Base interface
- HUB 1.375x24
- Front cap
- StingerWorx MDS
The HUB 1.375x24 is an open standard: 494 mounts and 940 muzzle devices in our catalog fit this suppressor, including StingerWorx HUB to Direct Thread Mount 1/2x28, AAC 51T S.T.A.M.P. Mount and AB Suppressor AB Raptor Adapter. You aren't locked into one manufacturer's parts.
Which ones fit your barrel and host?
Check in the BuilderThe Thunder Beast Silencer Summit fires every suppressor entered on the same gun, with the same equipment. Venom 300 was measured in 2 tests. Figures can only be compared with others from the same test, so each one links to everything else fired on that gun.
Bolt-action and lever rifles
Gas-operated rifles and carbines
Measurements published by Thunder Beast Arms Corp. How to read these
Manufacturer claim
- Dual Path Suppression Technology splits expanding gases into two separate pressure zones, reducing peak blast pressure and optimizing sound suppression.
- Built with the industry-standard 1.375x24 TPI HUB interface.
- Swap the included flat cap for a Flash Hider for up to 75% flash reduction over the suppressor alone, or for a Suppressor Brake endcap for added recoil and ground effect management.
- User serviceable: with the StingerWorx Universal Suppressor Clamp and basic tools like a crescent wrench, shooters can disassemble, clean and reassemble the suppressor in minutes, and worn components can be replaced or upgraded without replacing the entire unit.
Show all 10 ▾ ▴
- Combines a titanium blast chamber and blast baffles with a Type III hard anodized 7075 aluminum tube and secondary baffles.
- Painted with Cerakote Transfer Grey, one of Cerakote's submicron coatings designed to maximize heat transfer and cool the suppressor faster.
- Purpose built for magnum-class cartridges such as 300 PRC, 300 Weatherby and 300 RUM, rounds with massive powder columns that demand more volume to suppress effectively.
- Includes a Modular Device System lock ring and standard flat end cap, plus a titanium HUB Direct Thread Mount (5/8-24) or a HUB to Emperor Mount for use with the Emperor Muzzle Brake, which is sold separately.
- Calibers: 300 Caliber and smaller, optimized for 300 PRC, 300 Weatherby and 300 RUM.
- Full Auto Rated: No.
Is one of these wrong, or does our wording say something the source doesn't?
